10000kN quality inspection standard force gauge 300t high-precision force sensor

Description :

10000kN Quality Inspection Standard Force Gauge 300t High Precision Force Sensor Product Introduction and ExplanationCan carry out measurement value transmission of standard force measuring instruments with a range of 10N to 10000kN at levels 0.1 and 0.3; The standard device for hydraulic jacks and the calibration device for working force gauges provide after-sales technical support for technical testing and quality supervision of construction projects such as highways, railways, water conservancy and hydropower, and urban construction in Anhui Province; Each standard instrument of Youzhongli is strictly produced according to the ISO376 process, ensuring the transmission of force values during each azimuth rotation, and improving the long-term stability and quality of the product. Provincial and municipal metrology institutes, 0.3 level and 1 level metrology stations. Standard force gauges are equipment selected by various quality and technical supervision, metrological testing, research institutes, universities, quality inspection agencies, relevant departments, and enterprises. The product has a two-year warranty, good price, and fast delivery.

10000kN quality inspection standard force gauge 300t high-precision force sensor：

　　Measurement type: force measurement

　　Adaptive force meter level: 0.1%

　　Input signal range: 4.0mV/V

　　Optional channel specifications: 6/24/40

　　Excitation output voltage: 10V DC

　　Display digit size: 6-digit to 1.0 inch

　　Rated display division: 300000

　　AD conversion rate: 50 times/second

　　Repeatability and linearity: 0.005% FS

　　Gain temperature drift coefficient: 5ppm

　　MV/V accuracy: 0.02% FS

　　Communication printing interface: RS232

　　Power supply specification: 220V-50Hz

　　The instrument can be connected to a printer with an RS232 interface. The third pin (232TXD terminal) of the instrument digital interface is connected to the RXD terminal of the printer, the second pin (232RXD terminal) of the digital interface is connected to the BUSY terminal (CTS terminal) of the printer, and the fifth pin (GND terminal) of the digital interface is connected to the GND terminal of the printer. After installing a printer power supply module, the instrument can provide working power for the micro printer. External DC power supply module (or 4 or 5 1.5V battery power supply modules)

　　After installing a DC power supply module inside the desktop instrument, it has a charging function. It is recommended to use 6V lead-acid batteries or hydrogen ion batteries for external batteries, with a continuous output current greater than 350mA. The external battery is input through a circular Φ 2.5mm external battery socket on the back of the instrument, with the center of the socket connected to the positive pole and the edge connected to the negative pole. Turn on the instrument power switch to start working. External battery socket input polarity diagram input voltage range 6V~9VDC

　　★ Charging method: The instrument can charge the battery by connecting it to a 220V AC power source, turning on the instrument power switch, and then connecting the battery to the instrument to charge it. The charging current is about 200mA. For products after September 2009, the red circular charging indicator light in the lower right corner of the instrument display window will light up when charging. This module is not included with standard products.

　　★ 5th or 1st battery module: A module that can install 4 1.5V alkaline batteries or 1.2V rechargeable batteries. This module can be directly installed on the outside of the desktop instrument, making battery replacement convenient and fast. The use and charging are the same as the above method.

　　⑥ Connection between the instrument and USB interface, 485 interface, and isolated RS232 interface

　　When communication with USB interface devices is required, a USB ← → RS232 adapter cable can be purchased. Based on application experience, this type of adapter cable is suitable for driving

　　Generally, dynamic programs need to be run from the Windows Explorer. For specific installation steps, please refer to the product manual you purchased.

　　When communication with 485 interface devices is required, the built-in 485 module can be ordered from the product supplier. It is recommended to order the built-in isolated 485 module when communicating with multiple instruments.

AfterSalesService :

• 10000kN quality inspection standard force measurement