Handheld 18kg weight FQW15-16 pneumatic submersible pump FQW15-16/W mining pneumatic submersible pump lightweight

Description :

　　Handheld 18kg weight FQW15-16 pneumatic submersible pump FQW15-16/W mining pneumatic submersible pump lightweight

　　The weight issue of submersible pumps is highly controversial in the industry,FQW15-16 Pneumatic Submersible PumpThe introduction is late, but the pump has strong rigidity requirements and high operability.FQW15-16 Pneumatic Submersible PumpLightweight, it weighs only 18kg, is portable, energy-saving, and has a low price. I haven't introduced it to everyone yet, which is related to the lag factor in the transmission of public opinion to the decision-making level. Now, you are interested in this small and lightweightFQW15-16/W Mining Pneumatic Submersible PumpIf you are interested, let me give a brief introduction first.

　　1、 Take a lookFQW15-16 Pneumatic Submersible PumpStructure and working principle

　　1. The pump consists of three parts: pump body, air motor, and overcurrent.

　　2. Wind motor part: composed of rotor, blades, upper and lower end covers, cylinder, bearings, etc.

　　3FQW15-16/W Mining Pneumatic Submersible PumpThe upper milling of the rotor consists of five inclined slots at a 30 ° angle to the radial direction, with blades matched inside the slots. The upper and lower end covers each have a blowing eye. When the air pump is started, some of the air pressure blows open the blades inside the slots through the blowing eye, while a large amount of air pressure enters the cylinder from the main air duct to push the blades and drive the rotor to rotate.

　　4FQW15-16/W Mining Pneumatic Submersible PumpOverflow section: composed of a discharge chamber, water turbine, pump cover, anti fouling cover, etc. The water wheel adopts a semi open design and is directly installed at the lower end of the rotor shaft. The water wheel nut is tightened, the pump cover and anti fouling cover are installed, and the water wheel is put into the water. Then, the air pressure is sent into the rotor through the lifting handle inlet to drive the water wheel. Under the centrifugal force of the water wheel, the water is sucked into the discharge chamber and discharged along the outlet pipe through the outlet vortex.

　　IIFQW15-16 Pneumatic Submersible PumpMain technical parameters:

　　1. Flow rate: 16 cubic meters per hour

　　twoTheInlet diameter: 25mm

　　3. Lift: 15 meters

　　4. Exhaust port diameter: 25mm

　　5. Rated speed: 3000 revolutions per minute

　　6. Usage pressure: 0.4-0.5 megapascals

　　7. Load gas consumption: 1.5 m3/min

　　8. Exhaust cross-section: 18- Φ 6 (mm) hole

　　9. Diameter of outlet pipe: 38mm

　　11. Dimensions: (length x width x height) 230 x 200 x 350 (millimeters)

　　3、 FQW15-16 Pneumatic Submersible PumpLightweight, only about 18 kilograms.

　　If there is no danger, it is safe; if there is no damage, it is complete,FQW15-16 Pneumatic Submersible PumpFirstly, it is necessary to ensure the safety of underground pumping, as safety guarantees the protection of life and property from loss during the production process,FQW15-16 Pneumatic Submersible PumpLightweight and lightweight，It weighs only 18kg, as we have already explained earlier. We would like to emphasize safety again here becauseFQW15-16/W Mining Pneumatic Submersible PumpThe power source itself utilizes the abundant gas source in the mine, which does not generate hidden dangers such as sparks like electric pumps. Safety production is the management focus of enterprises and the fundamental guarantee for their development.

AfterSalesService :

• Pneumatic submersible pump