Hongyi QYW100-36 Pneumatic Sand Discharge and Sewage Submersible Pump Mining Pneumatic Submersible Pump High Flow

Description :

　　Hongyi QYW100-36 Pneumatic Sand and Sewage Submersible Pump, High Flow Mining Pneumatic Submersible Pump

　　toQYW100-36 Pneumatic Sand and Sewage Submersible PumpThe application of only a small amount of pumping and drainage is far from enough. The important thing isQYW100-36 mining pneumatic submersible pump with high flow rateIt is its strength, and we must dare to use it boldly to fully demonstrate its talents.

　　Hongyi Technology's Xiao Zhang will showcase to you todayQYW100-36 Pneumatic Sand and Sewage Submersible PumpIt can be said that it is a welfare product for many users becauseQYW100-36 Mining Pneumatic Submersible PumpIt is a drainage equipment powered by compressed air, and the power source cannot be compared with electricity, which may result in a flow rate that cannot meet the on-site requirements. However, the advantages of pneumatic submersible pumps are incomparable to explosion-proof electric pumps, and many customers are also very concerned. Now there is no need to rectify it. Our factory produces and sells this high flow submersible pumpQYW100-36 Pneumatic Sand and Sewage Submersible PumpThe overall structure is simple, easy to assemble, disassemble, maintain, and move. It is safe and reliable to use on work surfaces containing gas and coal dust, achieving a significant improvement in flow rate and demonstrating the true flow capacity of a pneumatic submersible pump!

　　QYW100-36Mining pneumatic submersible pump with high flow rateWhere is high efficiency reflected? Flow rate of 100~80 m3/hour; Lift of 20~38 meters; Please carefully consider these two important parameters.

　　Now let's take a look at this oneQYW100-36 Pneumatic Sand and Sewage Submersible PumpOther technical indicators:

　　1. Model QYW 100-36

　　2. Speed 3500-4000r/min

　　3. Outlet diameter: 3 inches

　　4. Dimensions 380 × 220 × 480mm

　　5. Using wind pressure of 0.4~0.7 megapascals

　　6. Gas consumption of 5-6m3/minute

　　7. Fuel consumption 50ml/s

　　8. The weight is approximately 38 kilograms

　　QYW100-36Pneumatic sand removal and sewage submersible pumpGeneral causes and elimination methods of faults

　　1. The exhaust pipe noise gradually decreases to disappear, and the air pump stops running.

　　QYW100-36Mining pneumatic submersible pumpAfter long-term operation, compressed air is expanded by the air motor and discharged through the exhaust pipe (muffler), taking away the surrounding heat energy and causing the inner wall of the exhaust pipe to freeze, gradually blocking the exhaust pipe. Use a hardwood stick to strike the exhaust rubber pipe, causing the ice cubes to break and blow away or stopping the air supply, allowing them to naturally melt before continuing to use. (It is best to install a water removal device for compressed air)

　　2. The startup operation is normal, but the flow rate and head are not large.

　　The wind pressure is too low, wait until the wind pressure rises to 0.5-0.7MPa before continuing to use.

　　3. The filter hole on the anti fouling cover (pump seat) is partially blocked, resulting in insufficient water absorption. Clean the anti fouling cover (pump seat) to ensure that the filter hole is unobstructed.

　　4. The pump body vibrates significantly during operation. The rotor shaft is bent or the bearings are worn out excessively. Adjust the pump shaft or replace the bearing.

　　QYW100-36Pneumatic sand removal and sewage submersible pumpThe drainage process is efficient and the results are satisfactory. Grassroots mine workers need toQYW100-36 mining pneumatic submersible pump has high efficiencyThe drainage tool is efficient and portable. Senior staff should pay attention to the needs of grassroots employees.

AfterSalesService :

• Pneumatic sand removal and sewage submersible pump