BQG450 Mining Pneumatic Diaphragm Pump with Few Vulnerable Parts Pneumatic Diaphragm Pump 1.5-inch Engineering Plastic Material

Description :

　　BQG450Mining pneumatic diaphragm pump, pneumatic diaphragm pump, mining pneumatic diaphragm pump

　　BQG450/0.2Mining pneumatic diaphragm pumpMainly used for mine development and vertical shaft construction in minesBQG450/0.2 Mining Pneumatic Diaphragm PumpThe drainage construction of underground chamber engineering is particularly suitable for mining working faces. We will persist in improving the quality of pneumatic diaphragm pump products to achieve customer satisfaction.

　　BQG450/0.2Mining pneumatic diaphragm pumpFeatures

　　BQG450/0.2Mining pneumatic diaphragm pumpBy driving the valve core back and forth with airflow, the compressed air alternately enters the left and right air chambers, causing the diaphragm to move back and forth and creating a pressure difference in the working chamber, achieving the purpose of water absorption and drainage. Small size, light weight, no need for foundation, can be used as a mobile pump, no lubrication required, the main valve has no special requirements for the air source, and can start and operate by self suction.

　　BQG450/0.2Mining pneumatic diaphragm pumpProduct features:

　　one pneumatic diaphragm pumpNo need for irrigation, with a suction height of up to 5m, a lift of 70m, and an outlet pressure of ≥ 6bar.

　　2. The flow is spacious and the performance is good, allowing particles with a diameter of up to 10mm to pass through. When pumping mud and impurities, there is minimal wear on the pump.

　　three BQG450/0.2Mining pneumatic diaphragm pumpThe head and flow rate can be infinitely adjusted through the opening of the air valve (the air pressure can be adjusted between 1-7 bar).

　　4. The pump has no rotating parts and no shaft seal. The diaphragm completely separates the pumped medium from the moving parts and workpiece medium of the pump, and the conveyed medium will not leak outward. So when pumping toxic, volatile or corrosive media, it will not cause environmental pollution and harm to people.

　　5. No need for electricity, reliable use in flammable and explosive places.

　　6. Can work submerged in a medium.

　　7. Easy to use, reliable in operation, and only requires simple opening and closing of the gas valve for starting and stopping. Even if the pump runs without medium for a long time or suddenly stops due to unexpected situations, it will not be damaged. Once overloaded, the pump will automatically stop, with self-protection performance. When the load returns to normal, it can automatically start running again.

　　8. The pump has a simple structure and few vulnerable parts. It is easy to install and maintain, and the medium transported by the pump will not come into contact with moving parts such as the valve and connecting rod. Unlike other types of pumps, the performance gradually decreases due to wear and tear of components such as rotors, pistons, gears, and blades.

　　nine BQG450/0.2Mining pneumatic diaphragm pumpCan transport viscous liquids (viscosity below 10000 centipoise).

　　ten pneumatic diaphragm pumpNo need for oil lubrication, even when idling, it has no effect on the pump, which is the characteristic of this pump.

　　BQG450/0.2Mining pneumatic diaphragm pumpTerms of Use

　　1. When transporting any flowable material, the medium concentration (volume ratio) shall not exceed 15%;

　　2. The diameter of solid particles does not exceed 9mm;

　　3. Working environment temperature (5-50) ℃;

　　4. The pH of the conveying medium is within the range of 6-8;

　　5. The temperature of the conveying medium shall not exceed 50 ℃;

　　6. Applicable pressure range: 0.4MPa to 0.8MPa.

AfterSalesService :

• BQG450 Mining Pneumatic Diaphragm Pump