Shandong Hongyi PZ-6 Dry Concrete Spray Machine Construction Spray Machine User Manual

Description :

　　PZ6Dry concrete spraying machine, construction spraying machine, concrete spraying machine

　　PZ-6Dry concrete spraying machineSurvival through quality, development through reputation, we doPZ-6 dry concrete spraying machineOur strategy is to seek quality, and our policy is to prioritize reputation.Construction spraying machineQuality comes from, value comes from belief.

　　PZ-6Dry concrete spraying machineProduct Features

　　one Construction spraying machineAdopting a universal wheel structure makes movement more convenient.

　　2. Straight through rotor type non bonded material chamber, smooth discharge, * * * time-saving.

　　3. Four point elastic compensation compression, good sealing effect, less dust near the machine, and long service life of vulnerable parts.

　　4. Adopting low-pressure high-speed vortex airflow transportation to overcome problems such as adhesion, pipe blockage, and pulse separation in material transportation, the material flow is uniform, continuous, and stable.

　　five Construction spraying machineThe nozzle adopts a discharge elbow device to improve the spraying effect, with less rebound and high spraying layer quality.

　　6. By using wear-resistant lining plates and rubber plates, the service life is greatly improved.

　　PZ-6Dry concrete spraying machineTechnical Specifications:

　　Production capacity: 6m3/h

　　Transmission distance: 200m

　　Applicable material ratio: cement/sand and gravel=1:3-5

　　Applicable material water cement ratio: ≤ 0.4-0.45

　　PZ-6Dry concrete spraying machineOrthopedic particle size: Φ 20mm

　　Inner diameter of conveying pipe: Φ 51mm

　　Work pressure: 0.2-0.4Mpa

　　Air consumption: 7-8m3/min

　　Loading height: 1.1M

　　Rotor speed: 11r/min

　　Power: 5.5kw

　　Construction spraying machineVoltage level: 380V or 660V

　　Machine gauge: 800mm

　　Dimensions (length x width x height): 1560 x 1100 x 1280mm

　　Whole machine weight: 700kg

　　PZ-6Dry concrete spraying machinecompose

　　1. Drive device (main motor, reducer, etc.)

　　2. Rotor assembly (rotor body, material chamber, rotor lining plate, etc.)

　　3. Wind system

　　4. Spray system

　　5. Electrical control system

　　6. Walking system.

　　PZ-6Dry concrete spraying machineInstructions for use and operating steps

　　The operator must carefully read the user manual and be familiar with the machine structure and operating procedures before starting work.

　　1. Preparation before startup: A. Check whether the connecting components of the whole machine are firm and whether the rotating and sliding parts are flexible and reliable. B、Construction spraying machineObserve the cursor and check if the lubricating oil in the gearbox is sufficient. C、 The drive motor is connected to the power supply. When inching the motor, observe that the rotation direction of the rotor should be consistent with the arrow direction. Otherwise, the power supply should be phase adjusted. D、 The main air circuit, upper air circuit, lower air circuit, vibrator air circuit, and nozzle water supply shut-off valve are in the closed state, and the main air pipe is connected to the air source. The water supply pipeline is connected to the water source, and the material conveying pipeline is connected to the main engine. E、 Adjust the clamping mechanism, manually pre tighten it first, then use a wrench to tighten the bent conveying pipe, open the main and upper air circuit shut-off valves, observe that the pressure gauge is around 0.3Mpa, and there should be no gas overflow at the rubber joint plate.

　　2PZ-6 dry concrete spraying machineThe spraying operation first opens the main air path, upper air path, and lower air path shut-off valves, opens the nozzle water supply shut-off valve, pre wets the rock surface, then starts the motor, opens the vibrator air path shut-off valve, adds the mixture to the hopper, and starts the spraying operation. During work, the nozzle operator should adjust the water supply of the nozzle appropriately to ensure that the concrete material has a suitable water cement ratio. The host operator should pay attention to observing the residual air holes on the side of the host. If excess material is discharged, the gas supply in the lower air path should be appropriately reduced. Until there is no material discharged from the residual air outlet of the machine and the equipment is working normally.

　　3PZ-6 dry concrete spraying machineBefore shutting down the machine, first stop feeding. If there is no material spraying from the nozzle, close the water supply shut-off valve. At the same time, add a small amount of wet sand and gravel to the hopper, and wash the residual materials in the hopper and rotor chamber several times. When there is no material spraying from the nozzle, turn off the motor power and all gas path shut-off valves.

AfterSalesService :

• Dry concrete spraying machine