2-meter belt sampling machine models are available in stock. 2000mm belt middle sampler

Description :

　　twoRice belt sampler, belt middle sampler, explosion-proof belt head sampler

　　We do2-meter belt sampling machineThe philosophy is to meet your requirements, be honest and meticulous in doing things. shape2-meter belt sampling machineProducts keep the corporate culture alive and thriving.Belt middle samplerLong lifespan, few vulnerable parts, easy to maintain. Let me introduce it to you below.

　　twoRice belt sampling machineCharacteristics of the system:

　　1. Adopting PLC control, with high degree of automation and reliable operation.

　　2. The system design is compact, space saving, and suitable for low space installation.

　　3Belt middle samplerThe modular structure facilitates on-site assembly and installation.

　　4. Careful design and material selection effectively prevent material blockage and scattering.

　　twoRice belt sampling machineSystem composition and principle:

　　According to the set time interval, the BET-SS sampling head rotates once and obtains a complete cross-sectional sample from the moving belt conveyor. The sample is directly fed into the primary belt feeder through the inclined chute, and the material is sent to the crusher. The crusher crushes the material to the required particle size without losing moisture, and then the sample is divided by the divider. Different sampling machines can be selected to meet the requirements of each type of sampling. The samples are collected in waterproof and dustproof containers.

　　twoRice belt sampling machineTechnical Requirements

　　processed materials

　　1. Name: Coal or Ore

　　2. Belt width: 1000 mm

　　three Belt middle samplerBelt speed: 1.6m/s

　　4. Conveying capacity: 800t/h

　　5. Feed particle size: ≤ 70mm

　　Note: The grabbing hopper can be adjusted for expansion and contraction according to the actual needs of the user.

　　twoRice belt sampling machinestructure

　　Belt middle samplerIt is a sample equipment designed to extract bulk materials from conveyor belts. It consists of a sampling head, a driving device, a position detection device, and a steel structural component with a dust cover. The sampling head is made of stainless steel. And equipped with a balance block. Installed on a steel structure. It is driven by a motor through a reducer, which drives a fan-shaped cutter to rotate once. Scrape a complete cross-sectional sample with the same opening as the cutter from the moving belt, and send the sample through the chute to the next sample preparation system for crushing and reduction.

　　twoRice belt sampling machineStructural characteristics:

　　1. Compact design, suitable for low space installation; No need for reposting points, can be directly installed on the conveyor, easy to install, low cost;

　　2Belt middle samplerUsing standard channel steel support can ensure sufficient rigidity;

　　3. Driven by a brake clutch motor, it can reliably stop the machine regardless of whether the belt is unloaded or fully loaded;

　　42-meter belt sampling machineThe side skirt of the equipment effectively prevents the scattering of materials;

　　5. Non contact proximity switch, used for start stop control;

　　6. Installing a limit switch on the belt sampling head effectively prevents the sampler from misoperation and the sampling head from falling above the belt surface when not in operation;

　　72-meter belt sampling machineSampling is representative, taking the entire cross-section at once, with a short sampling time for the sampling shovel to cut coal samples, close contact between the sampling shovel and the belt, and guide plates installed on both sides to ensure full cross-section sampling without damaging the belt;

　　8. Equipped with a balanced counterweight to eliminate high eccentric loads, reduce starting resistance, and ensure reliable positioning of the sampling head;

　　9Belt middle samplerEquipped with a coal flow detection device, when the coal flow on the belt meets the sampling standard, the PLC sends an action command and the sampling head moves. When there is no coal or less coal flow on the belt, the PLC does not issue any action commands and the sampling head does not sample. (It is also possible to manually start the sampling head on site according to the coal flow situation);

AfterSalesService :

• 2-meter belt sampling machine