AE102A oxygen filling pump inflation process mining oxygen filling pump can be filled with oxygen, nitrogen, carbon dioxide

Description :

　　AE102AOxygen filling pump inflation process Mining oxygen filling pump can be filled with oxygen, nitrogen, carbon dioxide

　　Oxygen filling pump for mining AE102A oxygen filling pump

　　enhanceAE102AOxygen filling pumpQuality is about reducing waste,AE102AOxygen filling pump inflation processOptimizing production conditions is a means of improving productivity. When optimizing production, successful people find methods, while unsuccessful people find excuses.

　　1The inflation process of AE102A oxygen filling pump:

　　This process is also the operation of filling oxygen from the gas source cylinder to the gas cylinder to be filled. The process is as follows:

　　(1) Connect the gas cylinder that needs to be inflated to the inflation joint;

　　(2) Turn on the gas source switch, intake switch, inflation switch, and gas cylinder switch in sequence. The oxygen in the gas source cylinder will automatically flow into the gas cylinder until the pressure is balanced.

　　(3) Turn off the collection switch for inflation. At this time, the pointers of the Class I pressure gauge and the electric contact pressure gauge rise with the increase of pressure. When the preset value is reached, the machine will automatically stop and the inflation process will end; Consultation: 400860537

　　(4) Turn off the inflated bottle switch and inflation switch, turn on the deflation switch, release the remaining air in the pipeline, and remove the inflated bottle;

　　(5) If you need to continue inflating, you can repeat the above steps. After the work is completed, stop the machine, turn off the gas source switch, turn on the collection switch, turn on the gas water separator switch, drain the residual gas in the pipeline, then turn off the gas water separator switch, air inlet switch, and cut off the power. When inflating again, the above steps should be repeated.

　　IIAE102A oxygen filling pumpNotes:

　　After the filling pump is completed, the power should be cut off, the gas cylinder switch should be turned off, and condensed water should be discharged from the gas water separator.

　　2. Use a small oxygen cylinder with a rated pressure of 30Mpa for oxygen filling at a pressure of 30Mpa.

　　The AE102A oxygen filling pump is an oxygen filling device used to increase the pressure of oxygen in a gas source bottle to another gas cylinder, so that the oxygen in the cylinder reaches the required pressure value. It is also suitable for extracting gases such as oxygen, nitrogen, carbon dioxide, etc. from the gas source bottle and filling them into the gas cylinder to be filled.

　　3. Before each inflation, the filling pump should be run idle for a few minutes to observe if all components are functioning properly. After normal operation, proceed with inflation; Once noise or other abnormal phenomena are found, the pump should be stopped for repair and used only after it is normal.

　　4. After running the filling pump for a certain period of time, if air leakage is found in the cylinder, the cylinder can be removed and the compression nut can be tightened with a special wrench (tightening the nut to a depth of about 1-1.5 buckles each time). If the compression nut has been tightened to the end, the compression nut can be replaced and the cylinder can be reinstalled on the filling pump for continued use.

　　5. The tap water of the cooling water tank should be connected properly and unobstructed to reduce the temperature.

　　During inflation, the surface temperature of the cylinder rises rapidly (about 60 ℃), which is a normal phenomenon.

　　7. The control pressure for automatic pump stop of the electric contact pressure gauge should be greater than the exhaust pressure of the safety valve, that is, the safety valve should be activated under normal circumstances, and the automatic control of the electric contact pressure gauge should only provide safety protection in exceptional circumstances.

　　IIIAE102A oxygen filling pumpWorking Principle:

　　1. When the plunger moves downwards, the gas in the cylinder expands and the pressure decreases. When the pressure in the cylinder is lower than the pressure of the gas in the gas source bottle, the suction valve on the cylinder automatically opens, and gas flows into the cylinder from the gas source bottle; When the plunger moves upward, the gas in the cylinder is compressed and the pressure increases. When the pressure is greater than the pressure of the gas in the cylinder to be filled, the exhaust valve on the cylinder opens, and the gas in the cylinder flows into the cylinder to be filled through the one-way valve and inflation switch on the gas water separator, completing one inflation.

　　2AE102A oxygen filling pumpThe working principle of the whole machine is to continuously reciprocate the plunger on the compressor to complete the oxygen filling work of the cylinder to be inflated. Namely: Start the electric motor, and the motor rotates through the pulley to drive the crankshaft on the compressor to rotate. The crankshaft's crankshaft turns through the connecting rod and crosshead to drive the plunger to make repeated up and down movements. Both ends of the cylinder are equipped with one-way valves, namely intake valves and exhaust valves, which control the direction of airflow. Therefore, the quality of the intake and exhaust valves has a significant impact on the gas efficiency.

　　strengthenAE102AOxygen filling pumpCommunication and cooperation bring you perfect and close connections and visible benefits,AE102AOxygen filling pumpQuality leads to market, improvement leads to progress, customers are gods, and the next process is customers. Shandong Hongyi looks forward to your inquiries and cooperation!

AfterSalesService :

• Oxygen filling pump