QYW70-60 Mining Pneumatic Submersible Pump with High Head and Large Flow QYW70-60 Pneumatic Submersible Pump for Sand Discharge

Description :

　　QYW70-60Mining pneumatic submersible pump with high head and large flow QYW70-60 pneumatic submersible pump for sand and sewage discharge

　　our factoryQYW70-60 Mining Pneumatic Submersible PumpProvide more convenient and efficient services for the pumping and drainage work of industrial and mining enterprises,QYW70-60 pneumatic submersible pump for sand and sewage dischargeWhat should we do if we don't have water? Perhaps it's just a small incident. Hongyi Technology Xiaozhang is dedicated to serving you 24 hours a day, serving enterprises, customers, and development.

　　1QYW70-60 Mining Pneumatic Submersible PumpWhat to do if there is no water supply? Let's take a look at two common causes of faults and their solutions:

　　1. Cannot start.

　　After the air pump is stopped, rock powder settles in the water, blocking the gap between the water wheel and the pump cover. Open the pump cover, remove impurities, and allow the water wheel to operate freely before use.

　　QYW70-60Pneumatic submersible pumpAfter continuous use for about ten days, due to the wear of the blades to a certain extent, they will get stuck between the cylinder and the rotor, preventing the rotor from rotating. Replace with new blades to restore normal operation (blade type).

　　Due to the cessation of wind and water return, the water wheel reversed and the water wheel nut loosened, causing the water wheel to sink and rub against the pump cover, making it difficult to start. Place the spring washer and tighten the water wheel nut

　　Rust or other impurities on the inner wall of the air duct enter the cylinder, trapping the blades in the rotor slot and preventing them from being blown out. Open the cylinder and clean the rotor and blades (blade type).

　　2. The operation is normal, but the flow rate has decreased or there is no water filling, and the pump is bubbling in the water.

　　The skeleton oil seal is worn or the sealing ring spring is loose. Turn on the air pump, replace the sealing ring or tighten the sealing ring spring.

　　IIQYW70-60 Mining Pneumatic Submersible PumpLet's take a look at the technical parameters:

　　1. Flow rate: 70 cubic meters per hour

　　2. Lift: 60 meters

　　3. Rated speed: 3000 revolutions per minute

　　4. Usage pressure: 0.4-0.5 megapascals

　　5. Load gas consumption: 1.5m3/min

　　6. Inlet pipe diameter: 25mm

　　7. Total weight: 31 kilograms

　　8QYW70-60 Pneumatic Submersible PumpDimensions (length x width x height) 350 * 200 * 500mm

　　What kind of pneumatic submersible pump is more suitable for you? Flow rate, head, outlet diameter, weight parameter indicators, etc. are important criteria for selecting pneumatic submersible pumps.QYW70-60 Mining Pneumatic Submersible PumpThis type of pneumatic submersible pump, based on the actual needs of domestic mining site construction, draws on the advantages of advanced foreign products of the same type and adopts a series of advanced processes, making it small in size, light in weight, novel in structure, easy to operate, easy to install, maintain and move.QYW70-60 Mining Pneumatic Submersible PumpDrainage operations in places with different environmental conditions, such as mining development, excavation of tunnels or vertical shaft construction. The blade type pneumatic motor is used in the power section, which is an ideal drainage tool for efficient mining excavation and well construction. AboutQYW70-60 Pneumatic Submersible PumpHave you understood the above explanation regarding the doubts about not being able to access water? If you have any further questions, please feel free to contact me at any time.

AfterSalesService :

• Mining pneumatic submersible pump