Hongyi produces FRZ50 pneumatic concrete vibration rod, which is lightweight and suitable for mining. It is a pneumatic insertion vibrator with noise

Description :

　　Pneumatic concrete vibrator, pneumatic insertion vibrator, FRZ-50 pneumatic vibrator

　　guaranteePneumatic concrete vibration rodQuality is our promise to you. wePneumatic concrete vibration rodSurvival through quality, development through quality, and efficiency through quality. Below is a brief introductionPneumatic plug-in vibrator.

　　Pneumatic concrete vibration rodComposed of a power part, pneumatic motor, and vibration part

　　1. The pneumatic motor is composed of a rotor, cylinder, upper and lower end caps, bearings, etc.

　　2. This pneumatic motor adopts a pre intake side blowing type, where compressed air enters the cylinder through the main air duct, pushes the blades, and drives the rotor to operate and work.

　　3Pneumatic concrete vibration rodThere are 6 ventilation holes on the main air duct of the cylinder, and 32 exhaust holes are staggered with each other for uniform blade wear

　　4. To increase the blade width and prolong the service life, five radial equal slots on the rotor are milled into R75 circular arc slots. Internally equipped with blades.

　　5Pneumatic plug-in vibratorOne 203 and one 305 single row radial ball bearing are respectively designed and installed inside the upper and lower end covers of the pneumatic motor to withstand axial torque. A J-shaped skeleton sealing ring is located at the lower end cover to prevent compressed air from flowing down inside the pneumatic motor, effectively ensuring the reliability, stability, and service life of the pneumatic motor transmission operation

　　Pneumatic concrete vibration rodUsage Tips

　　1. Should bePneumatic plug-in vibratorInstalled on a solid foundation, the anchor bolts should have sufficient strength and be tightened, while leaving an underground tunnel in the middle of the foundation for frequent adjustment and maintenance.

　　2. Before use, inspection and trial operation should be carried out to check whether the parts are intact. All fasteners, especially bearing seat bolts, eccentric block bolts, motor and gearbox bolts, should be firmly fastened.

　　three Pneumatic concrete vibration rodIt is not suitable to operate without load for a long time. In production operations, install sturdy and reliable template locking fixtures to ensure that the template and concrete table vibrate together.

　　4. The gears in the gearbox should be well lubricated and cooled due to high-speed and heavy loads; The oil level inside the tank should be maintained at the specified level, and the temperature rise during operation should not exceed 70 ℃.

　　five Pneumatic concrete vibration rodAll bearings of the vibration table should be regularly inspected and the lubricating grease should be replaced regularly to ensure good lubrication of the bearings. Attention should be paid to checking the temperature rise of the bearings. If there is overheating, measures should be taken immediately to eliminate it.

　　6. The grounding of the motor should be good and reliable, and the power cord and wire joints should be well connected. There shall be no damage or leakage.

　　7. The vibrating rod surface should be kept clean and flat regularly to ensure good contact with the steel mold. Due to the vibration of the countertop under high-frequency heavy load, cracks are prone to occur. Pay attention to inspection and repair in a timely manner. After completing each shift's homework, it should be cleaned promptly.

　　FRZ-50Pneumatic concrete vibration rodProduct Features

　　1 FRZ-50Pneumatic concrete vibration rodWidely applicable in the construction of municipal engineering, buildings, tunnels, culverts and other field projects with compressed air sources, various dry and hard concrete products and reinforced plastic concrete cast-in-place components are particularly suitable and reliable for vibration compaction engineering.

　　2 FRZ-50Pneumatic concrete vibration rodIt has the advantages of compact structure, small volume, light weight, low noise, large amplitude, high frequency, and can be adjusted (according to on-site usage requirements, the inlet air pressure can be used to adjust the essence).

　　3. Soft shaft transmission, with a reasonable structure, easy connection, installation, operation, maintenance, and use, not limited by power supply, humidity, and other conditions, is particularly suitable for use in special industrial and mining conditions.

　　4. The supporting vibration rod rubber hose is made of 65Mn steel wire tube, and the material of the rod head is alloy and 40Cr. The connection between the rod head and the hose is equipped with alloy guard springs or thickened, which is more durable than ordinary vibration rods.

AfterSalesService :

• FRZ50 Pneumatic Concrete Vibration Rod