FRZ-50 plug-in pneumatic vibrator, one person controls mining ZNF-50 pneumatic vibrator

Description :

　　Insertion type pneumatic vibrator, ZNF-50 pneumatic vibrator, 50 pneumatic vibration rod

　　Plug in pneumatic vibratorReputation comes from quality, quality comes from quality, we doPlug in pneumatic vibratorSelf improvement, healthy competition, mutual appreciation and support, mining wet dust removal fans make progress every day and embark on the path of success.

　　Plug in pneumatic vibratorPurpose and Features

　　1. ThisZNF-50 Pneumatic VibratorWidely applicable in the construction of coal mines, municipal engineering, buildings, tunnels, culverts and other field projects with compressed air sources, various dry and hard concrete products and reinforced plastic concrete cast-in-place components are particularly suitable for vibration compaction engineering.

　　2Plug in pneumatic vibratorIt has the advantages of compact structure, small volume, light weight, low noise, large amplitude, high frequency, and can be adjusted (the frequency can be adjusted according to the on-site usage requirements using the inlet air pressure).

　　3. Soft shaft transmission, with a reasonable structure, easy connection, installation, operation, maintenance, and use, not limited by power supply, humidity, and other conditions, is particularly suitable for use in special industrial and mining conditions.

　　4. The supporting vibration rod rubber hose is made of 65Mn steel wire tube, and the material of the rod head is alloy steel 4OCr. The connection between the rod head and the hose is equipped with alloy guard springs or thickened, which is more durable than ordinary vibration rods.

　　Plug in pneumatic vibratorMain technical parameters

　　Diameter: 32, 38, 50, 70mm available for selection

　　Total length: 6000 millimeters (excluding power part) Available in lengths of 4M, 6M, 8M, 10M, etc

　　Power: Blade type pneumatic motor

　　Rated speed: 3000 revolutions per minute

　　Plug in pneumatic vibratorWind pressure used: 0.4-0.5 megapascals

　　Load gas consumption: 1.5 m3/min

　　Exhaust cross-section: 32 × Φ 5 (mm) hole

　　Outer diameter of air inlet joint: 25mm

　　ZNF-50Pneumatic vibratorVibration frequency (in air): 3000 times/minute

　　Lower amplitude (in air):>12 millimeters

　　Total weight (including vibrating rod): 27.5 kilograms

　　Plug in pneumatic vibratorUsage, precautions and maintenance

　　ZNF-50Pneumatic vibratorIt is a high consumption product, which refers to the use of vibrating concrete during the pouring of concrete components, to evenly distribute coarse aggregates throughout the concrete components to prevent voids and segregation of the concrete. A complete vibrating rod product consists of 15 accessories such as rubber hose, vibrating rod head, flexible shaft, oil seal seat, etc.

　　1ZNF-50 Pneumatic VibratorAfter being connected to the flexible shaft of the vibrating rod, it should be vented smoothly before use. First, test run for 1-3 minutes to check if the operation is normal and if the startup is flexible. If there are no abnormalities, it can be put into use. If the vibrating rod does not produce any vibration, the end of the vibrating rod can generally be knocked to the ground. After the vibration produces a stable and powerful sound, the vibration operation can be carried out.

　　2Plug in pneumatic vibratorWhen working, the vibrating rod should be inserted vertically or obliquely into the concrete and vibrated for a certain period of time. During vibration, the vibrating rod should be pulled up and down.

　　3. In the case of pouring components or building layers, when vibrating the next layer, the vibrating rod should be inserted into the already vibrated layer to eliminate interlayer joints and achieve the overall effect.

　　4Plug in pneumatic vibratorAfter working continuously for half an hour, it is necessary to stop for a period of time to prevent excessive mechanical heating and damage to the components.

　　5. To protect the soft pump and hose, the bending radius during use should not be less than 500mm.

　　6ZNF-50 Pneumatic VibratorAfter every 50-100 hours of use, all parts inside the rod should be disassembled for cleaning. When disassembling, the pointed end and hose connector (all left screws) can be unscrewed, and then the large-diameter end of the roller cone should be struck with a wooden top hammer to remove the roller cone, bearings, oil seals, etc. Then remove the hose connector (right screw) to remove all parts.

　　7ZNF-50 Pneumatic VibratorAfter cleaning, replace the damaged parts and reinstall. Remove oil stains from all parts except for bearings. The conical surface and the casing should be free of oil.

　　8. The installed vibration rod is tightly connected with one end threaded to prevent the leakage of mortar water into the rod, which may cause the vibration rod to not vibrate.

　　9. InPlug in pneumatic vibratorDuring use, if it is found that the vibrating rod is not vibrating or weak, the vibrating rod can be disassembled to check whether the oil seal inside the rod is damaged. If it is intact, the oil stains inside the sleeve and on the cone can be wiped clean to eliminate the fault.

AfterSalesService :

• Plug in pneumatic vibrator