Inner Mongolia Pneumatic Concrete Vibrator FRZ-50 Pneumatic Vibration Rod Use and Maintenance

Description :

　　Pneumatic concrete vibrator, pneumatic vibration rod, pneumatic vibration rod

　　Pneumatic concrete vibratorGood, quality is more important than cost,Pneumatic concrete vibratorEntering the world of quality brings infinite business opportunities. procurementPneumatic vibration rodMore communication, less complaints; More understanding, less dispute.

　　Introduction to Pneumatic Concrete Vibrator:

　　Pneumatic vibration rodMainly used in mines, with a total length of 6m. Easy to operate. Pneumatic oscillator is a specialized tool for mine construction. It has the characteristics of small size, high oscillation frequency, and simple insertion into concrete for work, especially with improved connection equipment and simpler operation. It is an oscillator for coal mines and well construction

　　Pneumatic concrete vibratorStructure and operating principle:

　　The oscillator is divided into two parts: power and oscillating rod. The power is generated by a blade type pneumatic motor, which is mainly composed of four parts: rotor, cylinder, upper and lower end caps, and bearings. This pneumatic motor adopts an intake side blowing type, where compressed air enters the cylinder through the main air duct, pushes the blades, and drives the rotor to operate. The oscillating rod is divided into three commonly used types: 4m, 6m, and 8m, and can also be customized according to customer requirements.

　　Pneumatic concrete vibratorMain technical parameters

　　Diameter: 50mm

　　Total length: 6000mm (excluding power part)

　　Power: Blade type pneumatic motor

　　Rated speed: 3000 revolutions per minute

　　Wind pressure used: 0.4-0.5mp

　　Load gas consumption: 1.5m3/min

　　Exhaust cross-section: 32 × Φ 5 (mm) hole

　　Outer diameter of air inlet joint: 25mm

　　Vibration frequency: 3000 times/min

　　Lower amplitude:>12mm

　　Total weight: 27.5kg

　　Pneumatic concrete vibratorRod head diameter available: 32,38,50,70mm

　　Pneumatic vibration rodThe length of the flexible hose shaft is available for selection, including 4M, 6M, 8M, 10M, etc

　　(The commonly used vibrating rod for coal mine well construction is 6 meters long, with a rod head diameter of 50mm. Other specifications need to be customized.)

　　Pneumatic concrete vibratorUsage and Rest:

　　thatPneumatic vibration rodPneumatic motor, compact structure, internal components, requiring careful maintenance by the operator.

　　Before use, the exhaust sleeve should be rotated 30 ° to align the holes and ensure smooth exhaust. After a 3-5 minute trial run, check if the operation is normal and if the startup is flexible. If there are no abnormalities, it can be put into use (if the vibration head does not move, the vibration head can be straightened with the wind motor part and lightly tapped on the ground).

　　2. The inner diameter of the air inlet hose shall not be less than 25 millimeters, and the air pressure shall not be less than 4-5 kilograms per cubic centimeter.

　　When connecting the air supply duct, the dirt inside the duct and at the joint should be blown clean to prevent debris from entering the cylinder and causing component wear or rotor jamming.

　　four Pneumatic concrete vibratorDuring use, the vibration frequency can be adjusted by controlling the inlet air pressure according to the on-site requirements.

　　five Pneumatic vibration rodStop using, rotate the exhaust sleeve 30 ° to close the exhaust hole to prevent impurities from entering the cylinder through the exhaust port.

　　When repairing the wind motor, sufficient lubricating grease (No.2 calcium based grease SYB1401-62) should be added to the bearing chambers of the upper and lower end covers to ensure the lubrication of the bearings.

　　7. If stored for a long time, it should be disassembled, cleaned, coated with oil, and sealed to prevent rusting.

　　8. If the wind motor blades are severely worn, they will jam the rotor and not work. At this point, you can unscrew the handle and use M10 rivets to push out the end cover, thereby removing the blade for deburring or replacing it with a new one.

AfterSalesService :

• Pneumatic concrete vibrator