Lightweight ZBQ27 Pneumatic Grouting Pump for Coal Mines

Description :

　　Pneumatic grouting pump for coal mines, ZBQ27 pneumatic grouting pump for coal mines, ZBQ pneumatic grouting pump for mining

　　doPneumatic grouting pump for coal minesCustomer first, technology leading, unity and cooperation, seeking truth and pragmatism,Pneumatic grouting pump for coal minesSuitable for various types of mines,ZBQ-27/1.5 Pneumatic Grouting Pump for Coal MinesBased on service, survive on quality, and seek development through technology.

　　ZBQ-27/1.5Pneumatic grouting pump for coal minesFeatures:

　　1, Pneumatic grouting pump for coal minesSmall size, light weight, suitable for frequent movement and multi-point grouting in terms of mobility and handling.

　　2. Due to the use of pneumatic transmission, the grouting performance of the pump is very suitable for working conditions where a large flow rate is required when the grouting pressure is low, and a small flow rate is required when the grouting pressure increases.

　　3. Due to the use of pneumatic transmission, it can also be used in flammable, highly explosive, water dripping, dusty and other working environments.

　　4, Pneumatic grouting pump for coal minesUnder conditions where the slurry ratio requirement is not very strict, dual fluid injection can be achieved with just one pump, greatly reducing the cost of purchasing construction equipment.

　　ZBQ-27/1.5Pneumatic grouting pump for coal minesModel meaning:

　　Z: Grouting B: Pump Q: Pneumatic 27: Rated flow rate 27L/min 1.5: Rated working pressure 1.5Mpa

　　ZBQ-27/1.5Pneumatic grouting pump for coal minesProduct advantages:

　　1. The grouting pump adopts pneumatic transmission, has a small volume, light weight, and can be relocated with only one or two people.

　　two Pneumatic grouting pump for coal minesCan work in severe and harsh environments such as flammable, explosive, dusty, and rainy Egypt.

　　3. It can be infinitely adjusted and automatically variable with constant pressure, that is, the discharge volume decreases with the grouting pressure.

　　ZBQ-27/1.5Pneumatic grouting pump for coal minesScope of application:

　　Pneumatic grouting pump for coal minesIt is used for water plugging, gap filling, broken rock processing, viscous liquid, foam material transportation. It has functions such as explosion resistance, corrosion resistance, sedimentation prevention, low noise, and energy saving, and can be used in harsh conditions such as heavy water and high gas. The device has a compact structure, advanced and reasonable design, uses working medium to transmit pressure signals, forms a closed-loop automatic control performance, has no overpressure problem, is easy to use and maintain, has a small size, is easy to carry, and can be quickly moved to various work locations.

　　ZBQ-27/1.5Pneumatic grouting pump for coal minesInstructions for using optional accessories

　　1. Connect the oil pot in series with the intake pipeline, unscrew the oil pot nut, add lubricating oil, use a screwdriver to tighten the screws inside the oil pot, then reverse a small angle to obtain a satisfactory amount of lubricating oil, and then tighten the oil pot nut.

　　2. The pressure gauge and the pressure gauge socket are sealed with oil and are usually not removable.

　　three Pneumatic grouting pump for coal minesThe pressure gauge pipe joint is connected to the grouting port on the tunnel wall. It should be cleaned immediately when stopped from use. If necessary, the pressure gauge seat can be removed to remove the material accumulated at the diaphragm. Sharp tools should not be used to damage the diaphragm during removal.

　　Before disassembling the discharge pipe, the pressure relief valve should be opened first to relieve pressure.

　　ZBQ-27/1.5Pneumatic grouting pump for coal minesOperating Procedures

　　1. Ensure that the gas source is free of excessive moisture and dirt, and ensure the lubrication system of the gas source oil. Optional oil mist generator provided by our factory.

　　2Pneumatic grouting pump for coal minesThe air source pipe should first be connected to the ventilation pipe to blow away debris, and then reliably connected to the grouting pump.

　　3. Firstly, immerse the inlet of the pump in clean water and slowly open the inlet ball valve to ensure that the grouting pipeline is unobstructed and the seal is in a leak free state.

　　4. The slurry should be mixed evenly, without lumps, but thick. Timely clean the solidified materials at the corners and edges of the bucket to prevent them from being mixed into the slurry.

　　5ZBQ-27/1.5 Pneumatic Grouting Pump for Coal MinesImmerse the grout inlet into the slurry, slowly open the inlet ball valve, and gradually reach the appropriate grouting speed.

　　6. After the pump stops working, it should be immediately immersed in clean water for flushing, and the inlet ball valve should be slowly opened until the water discharged from the slurry pipe is clear and free of slurry.

　　7Pneumatic grouting pump for coal minesAfter cutting off the gas source and drainage pipe, regularly remove the screws from the flange, extract the grouting cylinder, and remove any remaining grouting material.

　　8. After cleaning, apply lubricating grease to the metal surface of the grouting cylinder and re connect it to the pump body for fixation.

　　9ZBQ-27/1.5 Pneumatic Grouting Pump for Coal MinesIt is strictly prohibited to operate the pump at high speed with no load or light load to avoid damaging various moving parts.

　　10. The pressure of the gas source shall not exceed 0.8MPa.

AfterSalesService :

• Pneumatic grouting pump for coal mines