100kg cantilever beam pressure sensor NB2-0.1t scale sensor price

Description :

　　100kg cantilever beam pressure sensor NB2-0.1t scale sensor price detailed explanation:

　　Non rotating torque sensor: YDN-2KC,YDN-5KC,YDN-10KC,YDN-20KC,YDN-50KC,YDN-100KC,YDN-200KC,YDN-500KC,YDN-1000KC,YDN-2000KC,YDN-5000KC

　　YDNF-2KC,YDNF-5KC,YDNF-10KC,YDNF-20KC,YDNF-50KC,YDNF-100KC,YDNF-200KC,YDNF-500KC,YDNF-1000KC,YDNF-2000KC,YDNF-5000KC,YDNF-10000KC

　　Compression force (weighing) sensor YA21S-150G,YA21S-300G,YA21S-600G,YA21-1K,YA21-2K,YA21-3K,YA21-5K,YA21-10K,YA21-15K,YA21-30K,YA21-50K,

　　YA32-60K,YA32-100K,YA32-150K,YA32-250K,YA32-300K,YA32-500K

　　Compression force (weighing) sensor: YD16-50K,YD16-100K,YD16-150K,YD16-300K,YD16-500K,YD16-1T,YD16-2T,YD16-3T,YD16-5T,D16-10T,

　　YC33-1K,YC33-2K,YC33-5K,YC33-10K,YC33-50K,YC33-100K,YC33-200K,

　　YC54-20T,YC54-50K,YC54-100K,YC54-200K,YC54-500K,YC54-1T,YC54-2T,YC54-3T,YC54-5T,

　　YC60-50K,YC60-100K,YC60-200K,YC60-500K,YC60-1T,YC60-2T,YC60-3T

　　YJ12-1T,YJ12-2T,YJ12-5T,YJ12-10T,YJ12-20T,YJ12-50T,YJ12-100T,YJ12-200T

　　YK53-10K,YK53-20K,YK53-50K,YK53-100K,YK53-200K,YK53-500K,YK53-1T,YK53-2T,YK53-5T,YK53-10T,

　　YK43-500K,YK43-1T,YK43-2T,YK43-3T,YK43-5T,YK43-10T,YK43-20T,YK43-50T,YK-3-100T,YK43-200T,YK43-300T,

　　YB45-10T,YB45-20T,YB45-30T,YB45-50T,YB45-100T,YB45-200T,YB45-300T,YB45-500T,

　　YB56-50K,YB56-100K,YB56-300K,YB56-500K,YB56-1T,YB56-2T,YB56-3T,YB56-5T

　　Pressure sensors are a commonly used type of sensor in industrial practice, widely used in various industrial automation environments, including water conservancy and hydropower, railway transportation, intelligent buildings, production automation, aerospace, petrochemicals, oil wells, electricity, ships, machine tools, pipelines, and many other industries. Below are some correct installation methods for pressure sensors

　　Usually, damage to high-temperature melt pressure sensors is caused by improper installation positions. If the sensor is forcibly installed in a small or irregularly shaped hole, it may cause damage to the sensor's diaphragm due to impact. Choosing a suitable tool to process the installation hole is beneficial for controlling the size of the installation hole. In addition, appropriate installation torque is beneficial for forming a good seal. However, if the installation torque is too high, it is easy to cause the high-temperature melt pressure sensor to slip off. To prevent this phenomenon, anti stripping compounds are usually applied to the threaded part of the sensor before installation

　　1. Correct installation method of pressure sensor:

　　(1) Verify the frequency response value of the pressure sensor under normal atmospheric pressure and standard temperature conditions using appropriate instruments

　　(2) Verify the correctness of the coding of the pressure sensor and the corresponding frequency response signal

　　2. Determine the specific installation location

　　To determine the number and specific installation position of the pressure sensor, it is necessary to consider each inflation section of the inflation net

　　(1) The pressure sensor must be installed along the cable and at the cable joint

　　(2) Each cable should be equipped with no less than 4 pressure sensors, and the two pressure sensors near the telephone office should be no more than 200m apart

　　(3) Install one at the beginning and one at the end of each cable

　　(4) Each cable should have one branch point installed. If two branch points are close together (less than 100 meters), only one can be installed

　　(5) One cable should be installed at the location where the cable laying method (overhead, underground) changes

　　(6) For cables without branches, due to the consistent cable program of the base line, the installation spacing of pressure sensors should not be more than 500m, and the total number should not be less than 4

　　(7) In order to facilitate the determination of the fault point of the pressure sensor, in addition to installing the pressure sensor at the starting point, an additional one needs to be installed at a distance of 150-200m from the starting point. Of course, in the design, economic and technical factors must be considered. If the pressure sensor does not need to be installed, it should not be installed

AfterSalesService :

• 100kg cantilever beam pressure sensor