HaiTe filter self-cleaning filter electric stainless steel self-cleaning filter fully automatic self-cleaning filter batch shipment

Description :

Self cleaning filter product introduction:

Self cleaning filter is a fully automatic online self-cleaning water filter, which is equipped with a set of stainless steel brushes, suction scanners, or a combination of wire brushes and suction inside the filter mesh. The above devices are driven by a reduction motor to rotate, and an electric drain valve is installed on the end cover or bottom of the filter. During work, turbid water enters through the inlet and filters out pollutants through a stainless steel wedge-shaped mesh. Purified water flows out from the outlet. When there is too much accumulation of dirt, it causes poor filtration and an increase in chamber pressure. When the pressure difference between the inlet and outlet water reaches a certain value (pre-set), the pressure difference switch sends a signal to the controller, which starts the reducer motor and drives the internal device to rotate and brush away or suck up dirt and impurities. At the same time, open the electric drain valve to discharge the dirt. The cleaning time is about 1 minute, and there is no need to cut off the flow during self-cleaning. The pressure loss of the drain does not exceed 0.05 MPa, and the flow loss does not exceed 1%. Brush filters overcome many disadvantages of traditional filtration products, such as small pollutant holding capacity, susceptibility to blockage by pollutants, need to disassemble and clean the filtering part, and inability to monitor the filter status. They have the function of filtering raw water and automatically cleaning and discharging the filter element. During cleaning and discharging, the system provides uninterrupted water supply, which can monitor the working status of the filter and has a high degree of automation. Covering various filtration precision requirements from 10um to 3000um, we provide customers with various water filtration equipment.

Self cleaning filter product features:

1. High strength 316L stainless steel (or alloy) sintered mesh with an accuracy of up to 2 microns is used. Through high-pressure backwashing at 2.0Mpa, the filter mesh is efficiently and thoroughly cleaned, and can be fully restored to its initial state. It can be used for life without the need for replacement.

2. The intelligent differential pressure filter has an automatic retrieval function and automatically realizes the functions of sewage discharge and high-pressure backwashing through various retrieved data. It can cope with unstable water quality fluctuations, operate fully automatically, and does not require manual intervention.

3. The control system is responsive, operates accurately, and has multiple setting functions for pressure difference, time, and manual operation. It can flexibly adjust the backwash pressure difference or time setting value according to different water sources and filtration accuracies.

4. Backwashing without interrupting normal water production, continuous operation, stable and reliable.

5. Backwash has a short duration and consumes only 0.001-0.002% of the normal water production, saving water, electricity, and energy.

6. The structural design is compact and reasonable, with few vulnerable parts, no consumables, low operation and maintenance costs, and simple operation and management.

7. Vertical or horizontal installation can be selected according to the installation site conditions, which is flexible and convenient.

Selection of self-cleaning filter products:

▲ System processing water volume, equipment inlet and outlet diameters;

▲ Requirements for impurity filtration accuracy;

▲ System operating conditions requirements, such as power source, pipeline pressure, spatial layout, temperature;

▲ Water quality status of filtered water bodies;

For situations involving strong acids, strong alkalis, or other special water qualities, users may require special customization;

▲ When filtering flocculent substances, brush cleaning should not be used in principle, and suction cleaning design should be used instead

Application areas of self-cleaning filters:

1. Air conditioning and HVAC system: effectively reduces suspended solids and turbidity, solves system blockage problems such as condensers and coolers, achieves the effect of descaling equipment and chemicals, and improves system operating efficiency;

2. Steel: used for water treatment filtration in raw material yards, sintering pellet plants, cooling water filtration in blast furnaces, rolling mills, continuous casting machines and other systems, and impurity filtration in high-pressure water phosphorus removal systems;

3. Automobile manufacturing: coating production lines, cooling circulating water systems, widely used in water treatment processes for automobile, tractor, motorcycle, and engine manufacturing;

4. Power plant: used for precision pretreatment of high-purity water preparation for power plant boilers, filtration of cooling circulating water and sealing water for generators;

5. Petrochemical industry: Performing side filtration treatment in circulating water plants, which can replace filter media filtration with single or multi machine parallel main treatment, reduce filter media filtration load, avoid a large amount of flushing water consumption, and save costs;

6. Agricultural landscaping and papermaking: In systems with nozzles and nozzles, equipment blockage and wear caused by impurities should be reduced. Therefore, high-precision and highly automated filtration products need to be selected;

7. Water supply and sewage treatment: used in pre-treatment systems to improve system operating efficiency;

8. Mining: Filter the underground sprinkler water to ensure the normal operation of the system;

9. Mechanical, food or other: Automatic and precise filtration of the system to prevent blockage of the cooling water system.

AfterSalesService :

• Self cleaning filter