Xinjiang barbed wire rolling cage manufacturer quotation: installation and construction of barbed wire fence, snake shaped knife price

Description :

　　The quotation from the manufacturer of Xinjiang barbed wire rolling cage for the installation and construction of barbed wire fence and snake shaped knife spikes is detailed as follows:

　　Composition of 0.5m diameter barbed wire rolling cage: barbed wire rope+knife barbed wire rolling cage+steel wire+column

　　Stinger rolling cage:

　　(1) The barbed wire rolling cage adopts blade barbed wire winding, and adjacent circles are fixed with barbed wire connecting clips every 120 degrees. After opening, it forms a snake belly network. After closing, the blade barbed wire winding diameter is 50cm. After opening, the installation spacing for each cross circle is 20cm

　　The diameter shall not be less than 45cm.

　　(2) The blade piercing rope is formed by mechanically rolling steel plates onto steel wires. The blade piercing width is 22mm, the vertical spacing between the blades is 15mm, the longitudinal spacing between the blades is 34mm, and the core wire diameter is 2.5mm. The Q195 steel plate mesh with a blade thickness of 0.5mm is punched and cut

　　make. The core wire is cold drawn from HPB300 Φ 6.5mm high wire.

　　(3) The barbed wire rolling cage is connected by a barbed wire connecting buckle and a longitudinal tension bar fixed on the bracket. The connection between the longitudinal reinforcement and the bracket is fixed by winding 2 turns of cold drawn galvanized steel wire with a diameter of 2.5mm and tightening it. The bracket is set on a 3m span protective fence

　　The columns and mid span positions of the fence, where the span is set to the upper part of the column, and the bracket is connected to the protective fence with bracket clamps. For protective fences that have already been installed with metal mesh sheets. The barbed wire rolling cage is directly made of cold drawn galvanized steel with a diameter of 2.5mm

　　The wire or barbed wire connection buckle is fixed to the metal mesh horizontal plate and metal wire.

　　(4) The vertical distance between the lower edge of the barbed wire rolling cage and the upper edge of the reinforced concrete protective fence is 0.05m

　　6. The gap between the lower part of the protective fence in steep slope areas and the ground is closed with C25 concrete, with a width of 180mm, and is flush with the two columns. It is buried below the ground with a depth of not less than 0.3m. Each unit should leave a 100mm drainage hole at the ground

　　Reinforced concrete column metal mesh protective fence

　　The reinforced concrete column metal mesh protective cabinet is composed of columns, mesh, and connecting components. The protective height is 1.8m

　　1. Column

　　The column is prefabricated with C30 reinforced concrete, with a cross-sectional size of 120mm × 120mm and a height of 2.2m. When prefabricating the column, a 42mm × 42mm square hole with a depth of 150mm is reserved in the middle of the top, and a connecting plate is inserted during on-site installation

　　Seal the Q235 square tube and fill the gaps with sealing material. The size of the square tube is 40mm × 40rn, with a thickness of 25mm. The length of the rectangular tube insertion end is 150mm. The exposed part is folded outward at an angle of 30 degrees, with a vertical consistency of 300mm. At the corresponding position of the column

　　Reserve three Φ 12mm circular holes and fix the connecting plates on both sides with screws during installation

　　2. Metal mesh sheet

　　The metal mesh adopts Jfl0235 short tube frame, with a specification of 30rrm × 50mm and a rectangular tube thickness of 2.0mm. The internal mesh wire is made of PB300 Φ 6.5mm high wire cold drawn, with a specification of 75mm × 150mm (Φ 4.0mm), and the upper part is folded outward

　　Angle 30 ', vertical height 300mm

　　3. Connecting plate and bolt

　　The column connection plate and mesh connection plate are made of Q235 copper plate with a 90 degree angle and a thickness of 4.0mm. They are divided into three forms: A, B, and C according to different usage positions.

　　The connecting plate and bolt are both made of Q235 steel and treated with galvanizing, with a galvanizing amount of 270g/m2

AfterSalesService :

• Quotation from Xinjiang Silk Roll Cage Manufacturer