Stainless steel water tank, welded stainless steel insulated water tank, stainless steel civil air defense water tank

Description :

Stainless steel water tank combination water tankManufacturing:

　　1. The welding rod used is stainless steel welding rod, all of which adopt tungsten inert gas shielded welding process;

　　2. Before welding, a groove should be made according to the regulations, and the dimensions formed outside the weld seam should comply with the regulations, and it should be ensured that there is no virtual welding or slag inclusion;

　　3. Smooth surface, no cracks, no bubbles in the weld seam, symmetrical arrangement of the lining structure, and no burrs;

　　4. At the end of the installation of the water tank, the inside and outside should be cleaned and decontaminated.

　　5. After the production and installation are completed, conduct a full water test to check for any water leakage. If there is any leakage, immediately modify it and make it aesthetically pleasing.

Stainless steel combination water tankPrinciple of designing the board into a convex shape

　　1. Improve the impact resistance of the water tank wall and the load-bearing capacity of the boundary layer of small water tanks. Everyone knows that stainless steel insulated water tanks are made of metal plates. If the wall of the water tank is not drum shaped, the boundary layer of the small water tank will be drum shaped due to water pressure, so everyone only needs to design it as drum shaped. It is the application of structural mechanics by designers. The use of metal plates can withstand greater pressure, thereby saving and controlling costs.

　　2. The reason for the overall increase in volume of the stainless steel water tank design is that the external drum can greatly enhance the volume of the stainless steel water tank, and the joint legs in the stainless steel water tank occupy a very large part of the volume.

　　3. Improve the welding characteristics of electric welding. If convex suspension is not used, then convex design is not used. During the assembly process, welded plates are difficult to avoid being affected by high-temperature deformation. The use of this design can reasonably disperse the strain judgment during the welding process and maintain the initial shape.

　　4. If hot water is stored at a higher temperature, it can reduce the impact of thermal expansion.

Stainless steel combination water tankThe internal structure

　　1. Bottom plate: Located at the bottom of the water tank, it is generally a 2 * 1 flat plate (normal specification), and the rest is cut according to the actual size of the water tank. The thickness is determined based on the size, foundation, size, and height of the water tank. Its thickness is generally 3.0~1.2

　　2. Side panel: Side panel sizes are divided into three conventional sizes: 1000 * 1000, 1000 * 500, and 500 * 500. It can also be flexibly adjusted according to the actual size of the water tank. The thickness is determined by the height of the water tank. Usually closer to the bottom. The thicker the board. Generally ranging from 2.5 to 1.2

　　3. Top plate: The specifications and models of the top plate and side plate are the same, with the difference being the thickness. The thickness of the top plate is thinner than that of the water tank. Generally 1.0mm

　　4. Manhole, escalator, ventilation hole: Manhole is an observation hole for entering the interior of the water tank for maintenance. Generally reserved near the inlet of the water tank, with a circular aperture of 800mm * 800mm and a manhole cover installed on top. The function of the escalator is for maintenance personnel to inspect and repair the top and interior of the water tank. The height of the escalator is determined based on the height of the water tank, with a height of 200mm higher than the water tank and a width of 300mm. The interval between each escalator should not exceed 350mm. The ventilation holes are used to prevent the expansion of air pressure inside the water tank and facilitate air circulation.

　　Note: Breathable holes and external openings must be equipped with insect proof nets. Prevent water sources from being contaminated by insects and rodents.

AfterSalesService :

• stainless steel water tank