Integrated sewage pump station production, sewage treatment, integrated pump station, fiberglass integrated prefabricated pump station manufacturer

Description :

Integrated sewage pumping station Fiberglass sewage pump station treatment 1. The integrated sewage pump station cylinder is made of fiberglass reinforced plastic. A composite material synthesized by reinforcing alkali free glass fiber and unsaturated resin matrix material, which has the characteristics of light and hard weight, non-conductive, low recycling, high mechanical strength, and corrosion resistance.

　　2. The integrated prefabricated pump station uses basket grilles or crushing grilles, which can effectively intercept impurities that exceed the allowable passage of the water pump, preventing oversized impurities from entering the cylinder and causing water pump blockage. The raised grille adopts strong corrosion resistance, light weight, and easy cleaning.

　　3. The integrated prefabricated pump station water pump adopts an automatic coupling installation method, which is convenient for disassembly and assembly during maintenance and repair of the water pump. The coupling body is made of ball milled cast iron material, and the guide rod and lifting chain are both made of stainless steel material. Make the water pump have good overall anti rust effect, high efficiency, low failure rate, and long service life.

　　4. All overcurrent components of the integrated prefabricated pump station are made of stainless steel material. The pipeline layout design is based on CFD fluid dynamics finite element analysis, with strong flow capacity, low resistance, corrosion resistance, and good noise reduction and shock absorption effects.

　　5. The control cabinet of the integrated prefabricated pump station pump room adopts an outdoor floor standing double-layer control cabinet. The control cabinet has manual operation, automatic operation, and remote control modes. In automatic operation mode, intelligent operation can be achieved, and it has protection functions such as overload, overcurrent, phase loss, and short circuit. It can set multi level start stop water pump mode and intelligent clearing function, with full protection and easy operation.

　　6. The integrated prefabricated pump station equipment is equipped with maintenance gate valves and sewage check valves according to the number of pumps. The valves are selected domestically and made of ball milled cast iron material, which has been electrostatically sprayed to effectively prevent valve body corrosion. The valve adopts a hard sealed structure, and the valve core is made of brass material, which can ensure long-term use in sewage environment and is maintenance free.

　　Environmental renovation is of great significance as it not only improves the environment but also reduces the workload of sewage treatment plants.

　　The drainage speed of the traditional concrete pump station of the integrated sewage pump station is very limited. Once encountering rainstorm and other situations, it is easy to lose the applied drainage capacity, and the ability to clear impurities is also very limited, which often leads to the trouble of blockage. With the development of society, urban life is getting faster and faster, and this type of concrete pumping station is facing the dilemma of being eliminated as its role in the environment is becoming smaller and smaller. At present, in response to market and social demands, fiberglass integrated prefabricated pump stations have begun to replace traditional concrete pump stations. Its emergence has effectively solved the problems of sewage treatment and upgrading, making great contributions to environmental protection.

　　In the construction of fiberglass integrated prefabricated pump stations, Jinze strictly controls product quality and constantly updates technology to meet the needs of society and market development. The integration degree of fiberglass integrated pump station is very high, so its footprint is small. The integrated prefabricated pump station also greatly reduces its construction and construction costs.

　　Selection of sewage pump station grating: 1. The driving shaft and driven shaft of the crushing type grating are made of 4140 (high-strength alloy steel) heat treated hexagonal steel, with a tensile tension of not less than 1000 kPa. The machine seal should be installed on the shaft sleeve to avoid direct contact with the shaft, reduce the impact of operating torque on the machine seal, and extend the service life of the machine seal. The crusher should be installed in the prefabricated pump station, and the water flow rate of each crushing type grating device should meet the sewage volume of the pump station. The bottom of the pit should be flat, and a layer of 10mm thick gravel layer should be laid on top. The concrete installation foundation can be pre constructed, directly poured at the bottom of the pit, or directly poured on the compacted layer, and the cement base plate should be horizontal. The upper surface of the base plate must be polished smooth.

　　2. Due to the fact that the conveying medium contains a large amount of sand, oil, and various household impurities, especially the high concentration of chloride ions in sewage. The cutting blade material of the crushing grid machine should have high strength and hardness conditions, and the equipment material should have seawater resistance function. The entire equipment should include a crushing type grille and auxiliary grille mesh bars to prevent garbage overflow during operation at ultra-high water levels, as well as channel support frames, suspension chains, foundation bolts, power control cables from the electrical control cabinet to the junction box and from the junction box to the motor, and all necessary accessories for safe and reliable operation.

　　3. The crushing type grille must be able to operate continuously under dry/wet conditions. To control future maintenance and replacement costs, it is necessary to provide a detailed explanation of the cutting blade and gasket forms used in the equipment, as well as detailed data on daily maintenance and replacement costs.

　　4. The motor is directly connected to the reducer, and the reducer is lubricated with oil bath. It should be suitable for severe vibration environments and have a shock absorption capacity of 500%. The output shaft is connected to the crushing grid through a two jaw coupling. The bottom of the pit should be flat, and a layer of 10mm thick gravel layer should be laid on top. The concrete installation foundation can be pre constructed, directly poured at the bottom of the pit, or directly poured on the compacted layer, and the cement base plate should be horizontal. The upper surface of the base plate must be polished smooth.

AfterSalesService :

• Integrated sewage pumping station