Tianjin Whole day Grain Feed Blender Crushed Straw Bundle Uniform Blender Traction Blender

Description :

　　Advantages such as easy mobility. It is a relatively advanced model. This series of mixers includes four main models: JZC250, JZC350, JZC500, and JZC750. The JZC750 model is a fixed type that can be used as a single machine or combined with a batching machine to form a simple mixing plant. All other models are mobile. The product structure is located inside the discharge cone of the mixing drum, with a pair of discharge blades welded. By changing the rotation direction of the drum, the concrete is pushed from the lower blades towards the discharge blades and discharged outside the drum. The mixing drum has four supporting wheels, and the mixing drum is driven by a motor through a gearbox to rotate the gear ring. Therefore, it still works in foggy and rainy weather. Firstly, the transmission system gearbox is a two-stage cylindrical gear reducer with a transmission ratio of 6.04248, a V-belt pulley tree ratio of 2.3912, a blocking gear ring ratio of 7.1111, and a total transmission ratio of 102.7467. The forward and reverse rotation of the mixing drum is achieved by reversing the direction of the motor. The feeding mechanism consists of an upper hopper, a ladder, an extension track, and a landing track, which are used to lift and flip the feeding hopper. The output shaft of the gear reducer is driven by the feeding clutch and wire rope drum at the shaft end, and the clutch is controlled by a manual control lever. The upper limit position of the hopper is automatically disengaged from the clutch by a limit device. After familiarizing themselves with this manual, users should conduct a detailed inspection and operation of the new machine, and familiarize themselves with the operating methods before putting it into production. The key points for inspection and trial operation are as follows:

　　1、 Placement of the machine

　　The site should be flat and the foundation should be solid. After the machine is in place, lower the four legs and place wooden blocks under them. Insert the pin into the appropriate hole and install the safety lock spring. Adjust the machine to a horizontal position, or lower the discharge port slightly. The landing track at the bottom of the ladder must be firmly padded, and the tires must also be properly padded to enhance the stability of the machine.

　　2、 Inspection and preparation work before trial operation

　　① Check the power supply voltage, with a rated voltage of 380V and a voltage fluctuation range of 340-410V, otherwise it may affect the normal operation of the machine or damage components.

　　② Check whether the wiring of the motor and electrical components is secure, and whether the grounding wire is correct. To ensure safety, the user installs a leakage protection device on the distribution board and then connects the power supply.

　　③ Pull out the oil size to check if the gearbox lubrication is good, and replenish and replace it if necessary at the specified oil level.

　　④ To connect the waterway, it is necessary to prepare a water bucket and place it near the water pump. Connect the suction valve, water pipe, and water pump together, and place the suction valve in the water bucket..

　　⑤ Check whether the connecting bolts of each part are tightened, especially the connecting bolts of the transmission components. If there is any inspection, they should be tightened.

　　3、 No load test run

　　① Start the mixing motor and observe whether the rotation direction of the mixing drum is consistent with the direction of the arrow on the mixing drum. If the direction is opposite, change the power wiring.

　　② Rotate the mixing drum in both forward and reverse directions, with a cycle of two minutes each, repeating for 15 minutes, to check for any element impact phenomenon, any abnormal noise in various parts, and whether the motor, gearbox, and hopper lifting are normal.

　　③ When the hopper is lifted to the upper limit position, is the limit set. 4、 Debugging of water supply system

　　① First, tap to check if the rotation direction of the water pump motor is correct. If it is not correct, change the motor wiring. Then, pull the suction pipe a few times, and the water pump will be able to supply water normally.

　　② Recheck the accuracy of water supply. If users have doubts about the accuracy of water supply, they can recheck it.

　　a、 Prepare a wooden barrel and remove one end of the rubber hose connected to the inlet pipe of the hydrogen mixing drum, and place it in the wooden barrel.

　　b、 Set the time relay to a certain time, and when the water pump reaches the predetermined time, the water pump will stop supplying water to check its water supply volume.

　　c、 Weigh out the amount of water in the bucket and check if it is the same as the predetermined value. If the repeatability error exceeds± 2%, the water pump suction should be checked based on the actual situation, whether it is blocked or leaking, until the water pump supply is stable. If there is a constant error in the retest result. The adjustable valve can be turned to adjust, operate and function.

　　5、 Check before each use

　　① Check if the machine is balanced, if all four legs are firmly supported, and if the ladder legs are firmly padded.

　　② The machine is running normally during air transportation.

　　③ Start the water pump and test it to ensure normal water supply.

　　④ Good electrical grounding.

　　6、 Operation precautions

　　① Every time the stirring material is added. Do not exceed the specified value. And the feeding hopper can only be lifted after the discharge from the mixing drum is completed.

　　② The hopper shall not be lowered arbitrarily. When special circumstances require lowering, the brake must be applied for a slow and balanced descent.

　　③ In order to reduce the sticking phenomenon of the hopper, the order of adding aggregates to the hopper should be:

　　Stone cement sand, or sand cement stone.

　　④ During the feeding process, water should be added in a timely manner to reduce picking time and dust accumulation.

　　⑤ When lifting the hopper, it is strictly prohibited for anyone to stay under the hopper. The empty hopper should be lowered slowly. To increase the service life of the machine.

　　⑥ The handle of the operating lever is strictly prohibited from being manipulated by non operators.

　　⑦ Pay attention to electrical safety, prevent the motor from getting damp, and prevent damage to electrical components and wires.

　　⑧ When there is a power outage, shaking the gearbox pulley with a crank can discharge the material inside the cylinder.

　　⑨ The gear ring and track must be lubricated with mechanical oil every shift.

　　⑩ Warning: If the switch is in the mixing (or discharging) position, it is strictly prohibited to quickly turn it to the discharging (or mixing) position to avoid damaging the gearbox gears.

　　Warning: The running in period is one month, during which the mixing load is halved. After one month, replace the gearbox gear oil and start working at full load.

　　7、 Maintenance after use

　　① Before stopping the machine, a certain amount of stones and water should be added, stirred for 3-5 minutes, and then released. This can be repeated several times to remove the accumulated material in the cylinder. After each shift, the accumulated material inside the cylinder must be cleaned up.

　　② Clean the accumulated dust and concrete adhered to the entire machine.

　　③ Place the hopper in the transport position and hang the safety hook.

　　④ Cut off the power and lock the electrical box.

　　⑤ During the freezing season, any remaining water in the slurry water supply system should be discharged.

　　⑥ Add necessary lubricating oil to each lubrication point as appropriate.

　　⑦ Warning: Refuel the clutch ring, bumper, and grease fitting once per shift.

　　8、 Precautions for towing

　　① Check if the fasteners of the walking system are loose and secure the drum and chassis with wire.

　　② The towing speed shall not exceed 15 kilometers per hour.

　　Machine maintenance

　　1. Check the gearbox oil level monthly and add or replace new oil if necessary.

　　2. Add lubricating grease to each oil cup every week.

　　3. The inner and outer brake bands of the feed clutch are worn out and cannot be used. They should be replaced with new parts.

　　4. Check whether the traction mechanism and front support wheel are damaged or bent.

　　5. The machine needs to be maintained once a year, with a major overhaul period of 4000 hours.

　　After-sales service

　　Manufacturer [Warm Reminder] The prices marked on the website are for reference only and may vary depending on the raw material prices. For specific price details, please consult by phone. Safety and reputation guarantee: only a small deposit is required to be paid in advance, and the logistics and express delivery can be made. The remaining balance will be paid upon arrival of the goods.

　　Guarantee: Within one year, if there is a need to replace machine parts due to non-human factors, the company will not only provide free replacement, but also bear the packaging and transportation costs of the parts.

　　Ordering method: Cash or transfer is acceptable. You only need to pay a 30% -50% deposit to cover the round-trip shipping cost before shipping. Logistics will be delivered to local county towns nationwide.

　　Shipping Deadline: All products sold are available and can be shipped by logistics on the same day of payment. * * It will not exceed 1-2 days and you can scan the waybill number to send it to you, so you can buy with peace of mind and wait with peace of mind! Ensure that the product you require is delivered to your shipping location within the specified time.

　　Our products are guaranteed for one year, and we are responsible for any non-human factors. The product is our top priority

AfterSalesService :

• Crushed grass bundle mixer
• horizontal TMR mixer for aquaculture