Shuttle mining car manufacturers supply shuttle mining cars. Characteristics of shuttle mining cars

Description :

　　The shuttle type mining car is an auxiliary transportation equipment in large section tunnel engineering that can both load and unload, with strong adaptability and high efficiency. It is installed on a walking mechanism with a steering device by a longer trough type body, and can travel on the track by locomotive traction. The bottom of the carriage is equipped with a scraper transport mechanism. During loading operations, it can use a jog method to load the slag from the loader to the loading end of the shuttle truck, and gradually transport it to the other end of the carriage through a scraper conveyor, thereby filling the entire carriage; When the traction locomotive drags the shuttle type mining car to the slag unloading yard, the scraper mechanism can also be used to unload the gravel in the entire carriage.

　　Advantages of shuttle mining car products

　　The continuous unloading speed is fast, the large storage capacity is large, the unloading efficiency is high and convenient, the ore slag does not settle at the bottom, does not contaminate the roadway, the ore block size is not limited, the use is flexible and convenient, and the equipment reliability is extremely high.

　　Application of shuttle mining car products

　　Shuttle type mining cars are used as transportation and storage equipment for slag removal, loading and unloading in tunnels, tunnels, mining operations, water diversion tunnels, diversion tunnels, oil pipelines, natural gas pipelines, tunnel excavation, and mining construction. They belong to the category of lifting and storage equipment.

　　Shuttle type mining car structure

　　It is mainly composed of the trough shaped carriages and running parts of the transport aircraft, and is pulled on the track by a traction electric locomotive. The vehicle is mounted on two bogies and equipped with a scraper or chain plate conveyor on the bottom of the carriage. It is driven by wind or electricity, and there are also wind and electricity dual-use options. Electric drive is commonly used for operation.

　　Operating Procedures for Shuttle Mining Cars: 1. The shunting operator must undergo training, be familiar with the performance, structure, and principles of shuttle mining cars, pass the examination, and obtain an operating certificate before they can operate.

　　Before starting the homework, prepare iron wedges and various tools, and lubricate each lubrication part according to regulations; Carefully inspect the bogie, connecting pins, traction bars, etc; Electric shuttle cars need to check the degree of damage to the outer skin of the cables and whether the electrical devices are damp. If they do not comply with regulations or pose a safety hazard, they should be repaired or replaced. Construction is not allowed when the state is abnormal.

　　3. Before loading the slag, the shuttle type mining car should run empty and observe that the transmission components are normal. The transmission chain and scraper transport chain should be free of looseness.

　　4. When connecting the electric shuttle car to the power supply, insulated gloves should be worn; After connecting the wind pipe of the pneumatic shuttle car, a slight tension should be applied to check the joint and confirm that it is secure before starting up.

　　5. When loading debris, iron wedges should be used to tighten the front and rear wheels. Personnel are not allowed to approach the shuttle truck to prevent it from being hit and thrown out by the rock loader, or to prevent injury from falling debris. When the driver needs to approach the work, the loading of debris should be suspended, and it is forbidden to use stone debris or wooden strips instead of iron wedges.

　　During the operation of the shuttle car, the driver should observe the condition of the machine at all times. If there are any abnormalities, the machine must be stopped immediately for inspection and troubleshooting. It is prohibited to continue operating the machine without proper handling when there are abnormal conditions.

　　After the shuttle car is fully loaded, the driver must remove the power or air source, remove foreign objects on the track, and then connect it to the electric scooter. After confirming the correct connection, remove the iron wedge before sending the driving signal.

　　8. When unloading debris, iron wedges must be used to tighten the wheels in both directions, and it is forbidden to use gravel or wooden strips instead of iron wedges. Confirm that there is no one in the unloading direction before starting the machine.

　　During shuttle transportation, it is prohibited to carry personnel.

　　10. After the work is completed, the shuttle car should be cleaned, pulled to a safe location for parking, and wedged tightly in both directions with iron wedges on the wheels.

　　11. The shuttle type mining car can be matched with a slag scraper for slag transportation. When reversing the shuttle mine car to the tail of the scraper, a handyman needs to command from behind.

　　zmjt055

AfterSalesService :

• Shuttle type mining car