RB-92S-4 Full Wind Vortex Fan 25KW Industrial Vortex Air Pump High Air Volume High Pressure Blower

Description :

　　RB-92S-4 Full Wind Vortex Fan 25KW Industrial Vortex Air Pump High Air Volume High Pressure Blower

　　high-pressure blowerPerformance characteristics:

　　1. Ultra quiet type, no noise: The motor runs directly, and by adding an integrated sound suppression device, the high noise of the high-pressure vortex air pump is improved, thereby achieving a silent effect.

　　2. High reliability: When the usage situation changes, the vortex air pump can still operate safely. Apart from the impeller, the high-pressure vortex air pump has no other actions, so its high reliability is almost maintenance free. The Longgu vortex air pump has the following advantages due to the use of precision outer bearings with good heat dissipation: high compression ratio; The operating temperature of the bearing is low; Long service life of lubricating grease; No maintenance required.

　　3. Easy to install and fully equipped, the vortex air pump can be installed and used at any time for compressed air or vacuum pumping, and can also be installed in any horizontal or vertical direction.

　　When the impeller of the oil-free and pollution-free high-pressure vortex air pump rotates, it does not come into contact with any parts and is free of lubrication, thus ensuring no pollution.

　　 This product has passed the European CE certification and CCC certification, and does not require any modifications. After testing, it can be used in Europe, America, Asia, and other regions!

　　High pressure fan, high-pressure blower, vacuum vortex air pump specifications:

　　Power: 0.18 KW 0.2KW 0.4KW 0.55KW 0.75KW 0.85KW 1.1KW 1.3KW 1.5KW 1.6KW 2.2KW 3.8KW 4KW 5.5KW 7.5KW 8.5KW 9KW

　　11KW 12.5KW 13KW 15KW 16.5KW 18.5KW 20KW 25KW 30KW

　　High temperature resistant type: 0.4KW 0.75KW 1.5KW 2.2KW 3.7KW 4KW 5.5KW 7.5KW 11KW 15KW 18.5KW

　　Single phase voltage: 0.12KW 0.18KW 0.2KW 0.4KW 0.55KW 0.75KW 0.85KW 1.1KW 1.3KW 1.5KW 1.6KW 2.2KW

　　Wind pressure: 50mbar-1040mbar (positive pressure: 8KPA-104KPA) (negative pressure: 8KPA-73KPA) (for the convenience of selecting different specifications, single-stage/two-stage models are available)

　　Airflow: 40m3/h-3000m3/h (for the convenience of selecting different specifications, both single-stage and two-stage models are available)

　　Frequency: 50HZ/60HZ

　　Voltage: 110V-200V-220V-280V-380V-400V-415V-440V-600-615V (universal voltage, applicable to all countries). If special voltage is required, it can be customized according to requirements

　　Pressure relief valve: RV-01 RV-02 (for use with)

　　Filter: MF08 MF10 MF12 MF16 MF20 MF32

　　high-pressure blowerThere are three main types of annular high-pressure blowers, including single impeller, double impeller, and triple impeller. Each of these three types has its own characteristics and can be considered as three types of annular high-pressure blowers with the same power. Their corresponding parameters are also different, so the cost prices of the three types are also different. Generally speaking, under the same power, the unit price of single impeller is the lowest, followed by double impeller, and finally triple impeller. Because adding one impeller also means thickening the fan casing, the cost is also high!

　　Parameter selection:

　　The main parameters for selecting a vortex high-pressure fan include power, air volume and pressure (which require certain requirements for calculation), voltage, etc.

　　Due to the widespread use of vortex air pumps, their selection method is the same as that of high-pressure fans. Generally speaking, the following two steps need to be followed:

　　1. Need to determine what function of the high-pressure fan is used on site, whether it is suction or blowing, and find the corresponding pressure flow curve of the high-pressure fan; If the curve is misread, sometimes the selected product cannot be used;

　　2. Based on the calculated pressure and flow rate, find the working curve above the corresponding working point that satisfies both pressure and flow rates on the curve graph; Then select the high-pressure fan model based on the working curve;

　　As long as it is a different work site, its requirements for pressure and flow rate are different, so in order to obtain relatively accurate data, relevant calculations need to be carried out. This needs to be done by designers or consulted with companies.

　　RB-92S-4 Full Wind Vortex Fan 25KW Industrial Vortex Air Pump High Air Volume High Pressure Blower

AfterSalesService :

• Vortex fan