Industrial high-pressure fan, full air high-pressure vortex fan, vortex type air pump, industrial oxygenation pump, blower

Description :

Industrial high-pressure fan, full air high-pressure vortex fan, vortex type air pump, industrial oxygenation pump, blower

RB-055 high-pressure annular blowerPrecautions for use:

　　1. Before using the fan for * times, it is necessary to carefully check whether the voltage and frequency indicated on the product nameplate meet local requirements, and strictly operate it according to the rated voltage of the motor

　　Before running the fan, it is necessary to check whether there is any collision or friction between the fan blades and the casing, whether the motor is grounded, and whether the insulation is good

　　Before running the fan, it is necessary to check whether the rotation direction of the impeller is correct. If there are any abnormal sounds or vibrations during the trial operation, the fan should be stopped immediately, the power should be cut off for troubleshooting, and it can only be used after it is normal

　　When the air intake of the fan is vertically downward or upward, the pressure bearing of the motor should be replaced before use

　　5. The temperature of mesons transported by the fan should not exceed 80 degrees Celsius

　　6. Fans should not be used in areas where water is easily sprayed or directly exposed to rain

　　7. Fans should not be used in environments where chemical gases are corrosive, flammable, or explosive

　　8. The foundation or support for fastening the fan must be firm

　　9. The connection of the fan pipeline network should be stable, and the weight of the pipeline should not be added to the various components of the fan

　　When a regulating valve is installed in the pipeline, the inlet regulating valve of the fan should be turned off before shutting down, and the outlet regulating valve should be slightly opened. After the fan is running normally, gradually open the regulating valve

　　Adopting high-strength aluminum alloy body, it runs for a long time without overheating; Smooth inner wall, flawless exterior, and lower operating noise; Adopting a wideband variable frequency motor, suitable for frequency conversion between 20-80 Hz, more energy-efficient and environmentally friendly; The manufacturing process of Siemens fan specific motors in Germany creates luxurious configurations for you The casting process of the air pump, our Xinke fan adopts one-time die-casting molding, with exquisite appearance, coupled with car paint, is comparable to imported fans. But we have met your quality requirements with a faster supply speed and more comprehensive after-sales service, at one-third the price of imported fans. Undoubtedly, our cost-effectiveness is higher than theirs.

high-pressure blowerOperation and maintenance:

After installation, the blower should be manually rotated before starting to check for any abnormal collisions or friction, whether the rotation direction of the motor is correct, and whether the inlet and outlet valves are in a low flow state.

2. During the operation of the fan, attention should be paid to whether there are any abnormal sounds, oil leaks, abnormal vibrations, high bearing temperature, excessive motor current, loose feet, or other abnormal phenomena inside the fan and motor, and they should be eliminated in a timely manner.

3. After 5000 hours of use, the bearing grease of the fresh air fan should be replaced.

4. Maintenance: When inspecting the casing, first loosen the screws on the horizontal split surface, open the upper half of the casing and the upper covers of the bearing boxes on both sides, and remove the rotor to repair the rotor or casing. During maintenance, special attention should be paid to whether the impeller blades are broken, whether there are cracks, and whether the main shaft is bent. Before installing and dismantling the machine casing, it is necessary to be careful to avoid damaging the rotor due to the swinging of the upper half of the casing during the installation and dismantling process.

5. During the shutdown period of the fan, the inlet and outlet of the fan should be covered properly to prevent debris from falling into the fan cavity and causing accidents.

6. The fan needs to be inspected every six months to remove dust and oil stains from the fan flow channel.

Installation precautions:

1. Installation location of high-pressure fan: It must be installed indoors in a place that is not affected by wind and rain

2. Environmental temperature: below 40 ℃

3. Relative humidity: below 80%

4. Air quality: If there are corrosive or flammable gases such as acids and alkalis in the air, they should not be transported by high-pressure blowers to avoid danger

5. Dust protection: Avoid using in places with large amounts of dust, powder, or fibers. If it is necessary to use in such places, please install a filter and regularly clean the dust attached to the filter and inside the high-pressure blower

6. Ventilation and heat dissipation: Please choose to use it in a well ventilated place and not in a sealed room or box

7. Placement space: For the convenience of column maintenance or repair, please avoid installing in overly narrow locations

8. Avoid vibration: Please install in a vibration free location; If the vibration in the venue is unavoidable, anti vibration measures must be installed to prevent the high-pressure blower from being damaged by external vibrations.

Industrial high-pressure fan, full air high-pressure vortex fan, vortex type air pump, industrial oxygenation pump, blower

AfterSalesService :

• Industrial oxygenation pump blower