BY-C series center surface curling high-speed slitting machine

Description :

　　detailed description:

　　Central surface curling high-speed slitting machineSuitable for slitting various roll materials such as BOPP, PET, CPP, CPE, PVC, paper, etc. During the production process, the materials can be trimmed and slitting according to different needs.

　　Performance and features:

　　1. This machine adopts a central winding and surface contact and winding method

　　2. The whole machine is centrally controlled by PLC and operated through a touch screen human-machine interface for centralized operation

　　3. Automatic meter counting, alarm and other functions;

　　4. The winding adopts A and B inflatable shaft structure, which is convenient for loading and unloading operations;

　　5. The unwinding adopts a photoelectric automatic correction system, which enables irregular materials to be cut normally

　　6. Flat blade longitudinal cutting waste edge automatic discharge device

　　7. Manual feeding, equipped with a 3-inch pneumatic valve shaft.

　　1、 Technical parameters

　　1. Width: 1100C type

　　2. Cutting thickness: 20g-300g/m2 (depending on different raw materials)

　　3. Raw material unwinding diameter: φ 800mm

　　4. Raw material winding diameter: φ 420mm

　　5. Cut raw material width: 1100mm

　　6. Diameter of the gas expansion shaft for winding: 2 pieces (tile type, can also be mechanical) with a diameter of 76m

　　7. Number of simultaneous coiling axes: 2

　　8. Correction accuracy: ± 2mm

　　9. Cutting accuracy: ± 0.5mm

　　10. Speed: 10-200m/min

　　11. Motor power: 5.5kw

　　12. Inverter power: 5.5KW 13. Body color: gray (other colors are optional)

　　14. Adopt automatic photoelectric correction (depending on different raw materials and specific customer requirements)

　　2、 Machine configuration

　　1. Unwinding section:

　　(1) The rack adopts a steel plate structure

　　(2) Magnetic powder tension control: tension control range 10-200N. M

　　(3) The tension brake magnetic powder used for material release is 10 kg per piece

　　(4) The transmission guide roller adopts aluminum guide rod, which has undergone dynamic balancing treatment (diameter 80 1130m)

　　(5) The substrate can be adjusted left, right, and parallel: manual operation

　　(6) One set of photoelectric correction system with correction accuracy of ± 0.5mm. The correction host is driven by one 110 type synchronous motor

　　(7) 1 photoelectric eye tracking correction

　　2. Roll up device

　　1) Structural method: Double air expansion shaft winding (can also be single axis winding)

　　(2) Two tile type inflatable shafts (specification: φ 76 × 1150m) are used

　　(3) Using 2 5kg magnetic powder clutches

　　(4) Transmission method: using gear and chain transmission

　　(5) Roll diameter: φ 420mm

　　(6) Unwinding diameter: φ 800 mm

　　(7) Compression method: using cylinder top sleeve structure and back pressure shaft device

　　4-way waste disposal device:

　　(1) Discharge method: Blow drying for waste disposal

　　(2) The main motor adopts a three-phase asynchronous motor (specification: 0.75kw), 1 set, 5

　　Control section:

　　The control system of this machine can be roughly divided into three parts: host control, tension control, and other control.

　　(2) Host control: including main motor control and main control box.

　　(3) Tension control: unwinding tension, winding tension, wide speed range controlled, with good performance at both low and high speeds

　　(4) Good performance, winding effect.

　　(5) Equipped with an electronic meter for measuring length; Alarm for parking; Automatic fixed length.

　　(6) Can be pre-set with cutting length shutdown

　　6. Supporting facilities: (User responsible)

　　(1) Power supply: three-phase four wire air switch: voltage 380V 50Hz

AfterSalesService :

• Slitting Machine